Lead2pass 300-360 Exam Questions Guarantee 300-360 Certification Exam 100% Success:
https://www.lead2pass.com/300-360.html
QUESTION 31
After the completion of a site survey with Ekahau Site Survey tool, using the default color palette, it is noted that multiple areas are shown as white on the heat map when viewing 5 GHz signal strength data. What does this indicate about the signal strength?
A. The area is below the minimum threshold configured on the tool.
B. The area is below the detectable level and indicates no RF signal.
C. The area is below -100 dBm at coverage cell edge.
D. The area is below -67 dBm at coverage cell edge.
Answer: A
QUESTION 32
An engineer must design wireless coverage in thick-walled stairwells. Which information should the engineer refer to when determining where APs can be installed?
A. Local or National Building Code
B. IEEE
C. BICSI TDMM
D. Cisco Hardware Installation Guide
Answer: D
QUESTION 33
An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services. Which of the following is a requirement for the design?
A. overlapping -72 dBm coverage from two access points
B. overlapping -67 dBm coverage from two access points
C. continuous -67 dBm coverage from one access point
D. continuous -72 dBm coverage from one access point
Answer: C
QUESTION 34
A network engineer is preparing for an office site survey with a height of 2.5 meters. Which three components are recommended to complete the survey? (Choose three.)
A. Use APs with external antennas.
B. Use DoS attack on APs while measuring the throughput.
C. Use APs with built-in antennas.
D. Use a battery pack to power APs.
E. Use a drawing of the office space to draw AP and client placements.
F. Use APs with directional antennas.
Answer: CDE
QUESTION 35
An engineer is planning for a 24 Mbps data rate for a new installation.
What is the coverage area from the AP if the environment and other factors are not taken into consideration?
A. 225 feet
B. 80 feet
C. 150 feet
D. 100 feet
Answer: A
QUESTION 36
Which two options describe best practices that must be completed after a wireless installation is finished? (Choose two.)
A. Make sure that there are no spaces between the devices on the rack that the Wireless Lan Controller isinstalled.
B. Consult with the customer to ensure that the IT staff has a complete set of design and installationdocuments.
C. Make sure the customer is aware that they should consider purchasing a support contract immediately afterthe installation is complete.
D. Spend time with the customer to show them the controller GUI and inform them how they can reach theCisco TAC if they have any problems.
E. Test all the customer’s wireless devices and applications to ensure they are working properly.
Answer: BE
QUESTION 37
A customer is deploying a Greenfield 802.11ac network on a floor that will support approximately 300 wireless devices. Which setting needs to be changed on Prime Infrastructure Planning Tool in order to predict the amount of access points the customer needs to service the new floor?
A. Data Coverage Support Margin
B. Demand Settings
C. Add AP Field
D. 802.11n Protocol Support
Answer: B
Explanation:
http://www.cisco.com/c/en/us/td/docs/wireless/prime_infrastructure/1-2/configuration/guide/pi_12_cg/maps.html#pgfId-1671104
QUESTION 38
What is the recommended minimum speed at the edge of the cells in an 802.11g network for a good Cisco VoWLAN deployment?
A. 11 Mb/s
B. 36 Mb/s
C. 12 Mb/s
D. 18 Mb/s
Answer: C
QUESTION 39
An engineer is conducting a location readiness test and wants a selected point to be considered location-ready. Which three possible configurations reflect the minimum number of APs needed? (Choose three.)
A. One AP is resident in each quadrant surrounding the point-in-question.
B. One AP per 1400 sq. ft. on the map.
C. Two APs are resident in each quadrant surrounding the point-in- question.
D. Four APs are deployed on the floor.
E. Three APs are within 70 feet (21 meters) of the point-in- question
F. Three APs are deployed on the floor.
Answer: ADE
Explanation:
http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Borderless_Networks/Unified_Access/CMX/CMX_LocFund.pdf
QUESTION 40
A network engineer is configuring QoS with a DSCP value of 46. To which queue must the CoS be mapped for priority queuing of the voice frames?
A. 1
B. 2
C. 5
D. 4
E. 3
Answer: C
300-360 dumps full version (PDF&VCE): https://www.lead2pass.com/300-360.html
Large amount of free 300-360 exam questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDU1VGRGVieEdJWGM
Maybe you also need:
Large amount of free 300-365 exam questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDSnBMTGlieXBLZWs
Large amount of free 300-370 exam questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDSTdRZ3dTUjVscVU
Large amount of free 300-375 exam questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDaUxFbEpISnFINk0